Hướng dẫn sử dụng AEG BHC92420XA Mũ đầu bếp

Hướng dẫn sử dụng

ENGLISH

The appliance must be installed by a qualified person in compliance with the instructions provided.

WARNING: Failure to install the screw or fixing device in accordance with these instructions may result

in electrical azard.

Only for hoods with electronic control:

The 4th speed (intensive) is automatically lowered to 3rd speed after 5 minutes of operation to optimise energy

consumption.

- If the hood is left on (lights and/or motor), after 10 hours in the absence of commands from the user, it will automatically

switch to OFF condition with all services switched off. In hoods with voltage 120V/60Hz this function is not active.

- In the event of interruption of power during the hood, if you restore the hood in the OFF state, then the engine must

be reactivate manually.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

Wear gloves when carrying out installation and maintenance operations.

DESCRIPTION

The unit can be found in filtering hoods, exhaust hoods or in hoods with an outside motor. In the Filtering hoods

(Fig. 1) the air and steam taken up by the unit are purified with charcoal filters and returned to the environment

through the aeration grids on the side of the flue. WARNING: When using filtering hoods, both charcoal filters

and an air deflector (A) must be used. Located in the lower part of the flue, this deflector recycles the air

to the environment. The charcoal filters are not supplied. In the Exhaust hoods (Fig .2) an exhaust duct conveys

the steam and cooking odors directly outside through the wall/ceiling. Therefore they do not require charcoal

filters. In the hoods with an outside motor (Fig. 3), a vacuum suction unit must be connected; this exhaust

will operate separately, conveying the exhaust air through the unit. Only use vacuum units suggested in the

original catalogue.

INSTALLATION

To facilitate installation, before starting remove the grease filters: press inward on the clamp at the handle and

pull the filter downward (Fig.4).

Wall fitting (Fig.5): Draw a line on the wall in vertical line with your hob. Mark the first 2 holes to be drilled

in the wall, respecting the distances indicated in Fig. 5. Drill the 2 holes and fit the screws (A) and screw anchors

provided. As already specified on the “Warning” sheet, bear in mind that the distance between the lower edge

of the hood and the hob must be min. 650 mm. Hang the hood (Fig. 6). Adjust the horizontal position moving

the hood to the right or left so that it is aligned with the wall units. When adjustment has been completed, without

removing the hood, mark the other 2 holes to be drilled (B) in the wall. Remove the hood and drill the holes

marked (8 mm diameter). Then use the 2 screw anchors and the 2 screws provided for final fixing (4.8x38mm).

To avoid damage make exclusive use of the holes already prepared on the hood.

Securing the telescopic flue: Basic installation requirements: – Set the electrical power supply within the space

covered by the decorative flue. – If your unit is installed in an Exhaust hood or in a hood with outside motor,

prepare the air exhaust hole.

Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the

notches on the centre of the bracket (Fig.7); using a pen, mark the 2 holes on the wall and then make the holes

and fit the screw anchors provided and proceed to secure the bracket using the 2 screws (provided).

Exhaust hoods and hoods with outside motors: connect the disposal duct to the air evacuation pipe of the hood;

use a flexible pipe and lock it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp

are not provided).

Only for models with outside motor (Fig. 8): plug the hood into the outside control unit using the special terminal block:

remove wire clamp A and lid B from the wiring junction box. Secure the wire connecting the control unit to terminal C.

Then replace wire clamp A and lid B on the wiring junction box.

Make all power connections to the hood by means of the power cable. Take 2 assembled flues and place these

on the upper surface of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using

the 2 screws (Fig.9).

Filtering hood: make all power connections to the hood using the power cable. Fasten the air baffle to the lower

flue as shown in Figure 10, using the 2 screws. Take 2 assembled flues and place these on the upper surface

of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.9).

Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such

filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:

- if the hood features round charcoal filters (Fig. 11), fit the charcoal filter by turning clockwise.

- if the hood features a panel type charcoal filter (Fig. 12), remove the two metal filter retainers (M) and position

the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter.

Định giá

Thông tin thêm về hướng dẫn này

Chúng tôi hiểu rằng thật tuyệt khi có sách hướng dẫn bằng giấy cho AEG BHC92420XA Mũ đầu bếp của bạn. Bạn luôn có thể tải xuống hướng dẫn sử dụng từ trang web của chúng tôi và tự in. Nếu bạn muốn có sách hướng dẫn gốc, chúng tôi khuyên bạn nên liên hệ với AEG. Họ có thể cung cấp hướng dẫn gốc. Bạn đang tìm kiếm hướng dẫn sử dụng AEG BHC92420XA Mũ đầu bếp của mình bằng ngôn ngữ khác? Chọn ngôn ngữ ưa thích của bạn trên trang chủ của chúng tôi và tìm kiếm số kiểu máy để xem chúng tôi có sẵn ngôn ngữ đó không.

Thông số kỹ thuật

Tất cả hướng dẫn sử dụng cho AEG Máy hút mùi
Thêm hướng dẫn sử dụng của Máy hút mùi

Câu hỏi thường gặp về AEG BHC92420XA Mũ đầu bếp

Đội ngũ hỗ trợ của chúng tôi sẽ tìm kiếm thông tin sản phẩm hữu ích và trả lời cho những câu hỏi thường gặp. Nếu bạn nhận thấy có sự không chính xác trong các câu hỏi thường gặp của chúng tôi, hãy cho chúng tôi biết bằng cách dùng biểu mẫu liên hệ.

Những sảm phẩm tương tự

Hướng dẫn sử dụng

AEG 825D-B Mũ đầu bếp

Hướng dẫn sử dụng

AEG BHG56750XA Mũ đầu bếp

Hướng dẫn sử dụng

AEG DBB3951M Mũ đầu bếp

Hướng dẫn sử dụng

AEG DEK6680M Mũ đầu bếp

Hướng dẫn sử dụng

Makano MKH-000002 Mũ đầu bếp

Hướng dẫn sử dụng

Makano MKH-000006 Mũ đầu bếp

Hướng dẫn sử dụng

Daikiosan DKH-000001 Mũ đầu bếp

Hướng dẫn sử dụng

Makano MKH-000009 Mũ đầu bếp

Thể loại liên quan